Testimonial - Keri Danielson REALTOR ®

Many thanks to Keri Danielson for the Richmond Home Inspection referral 

"Thanks for the inspection, good service and great value!"











Perry Lombard, CPI

Richmond Home Inspector

TPR valve discharge pipe missing

This can be dangerous.

More info on TPR valves here 

Temperature/pressure-relief or TPR valves are safety devices installed on water heating appliances, such as boilers and domestic water supply heaters. TPRs are designed to automatically release water in the event that pressure or temperature in the water tank exceeds safe levels.

It is critical that discharge pipes meet the following requirements, which can be found in InterNACHI’s Water Heater Discharge Piping. A discharge pipe should: 

1. be constructed of an approved material, such as CPVC, copper, polyethylene, galvanized steel, polypropylene, or stainless steel. PVC and other non-approved plastics should not be used since they can easily melt. 
2. not be smaller than the diameter of the outlet of the valve it serves (usually no smaller than 3/4"). 
3. not reduce in size from the valve to the air gap (point of discharge). 
4. be as short and as straight as possible so as to avoid undue stress on the valve. 
5. be installed so as to drain by flow of gravity. 
6. not be trapped, since standing water may become contaminated and backflow into the potable water. 
7. discharge to a floor drain, to an indirect waste receptor, or to the outdoors.  
8. not be directly connected to the drainage system to prevent backflow of potentially contaminating the potable water. 
9. discharge through a visible air gap in the same room as the water-heating appliance. 
10. be first piped to an indirect waste receptor such as a bucket through an air gap located in a heated area when discharging to the outdoors in areas subject to freezing, since freezing water could block the pipe. 
11. not terminate more than 6 inches (152 mm) above the floor or waste receptor. 
12. discharge in a manner that could not cause scalding. 
13. discharge in a manner that could not cause structural or property damage. 
14. discharge to a termination point that is readily observable by occupants, because discharge indicates that something is wrong, and to prevent unobserved termination capping. 
15. be piped independently of other equipment drains, water heater pans, or relief valve discharge piping to the point of discharge. 
16. not have valves anywhere. 
17. not have tee fittings. 
18. not have a threaded connection at the end of the pipe so as to avoid capping.

Thanks

Perry

Central Virginia Home Inspections

Three Deadly Mistakes Every Home Buyer Should Avoid

Three Deadly Mistakes Every Home Buyer Should Avoid

Deadly Mistake #1: Thinking you can't afford it. 

  

Many people who thought that buying the home they wanted was simply out of their reach are now enjoying a new lifestyle in their very own homes.  

  

Buying a home is the smartest financial decision you will ever make.  In fact, most homeowners would be broke at retirement if it wasn't for one saving grace -- the equity in their homes.  Furthermore, tax allowances favor home ownership. 

Real estate values have always risen steadily.  Of course, there are peaks and valleys, but the long-term trend is a consistent increase.  This means that every month when you make a mortgage payment, the amount that you owe on the home goes down and the value typically increases.  This "owe less, worth more" situation is called equity build-up and is the reason you can't afford not to buy. 

  

Even if you have little money for a down payment or credit problems, chances are that you can still buy that new home.  It just comes down to knowing the right strategies, and working with the right people.  See below. 

  

  

Deadly Mistake #2: Not hiring a buyer's agent to represent you. 

  

Buying property is a complex and stressful task.  In fact, it is often the biggest, single investment you will make in your lifetime.  At the same time, real estate transactions have become increasingly complicated.  New technology, laws, procedures, and competition from other buyers require buyer agents to perform at an ever-increasing level of competence and professionalism.  In addition, making the wrong decisions can end up costing you thousands of dollars.  It doesn't have to be this way! 

  

Work with a buyer's agent who has a keen understanding of the real estate business and the local market.  A buyer's agent has a fiduciary duty to you.  That means that he or she is loyal only to you and is obligated to look out for your best interests.  A buyer's agent can help you find the best home, the best lender, and the best home inspector in your area.  That inspector should be an InterNACHI-certified home inspector because InterNACHI inspectors are the most qualified and  best-trained inspectors in the world.

Trying to buy a home without an agent or a qualified inspector is, well... unthinkable. 

  

  

Deadly Mistake #3: Getting a cheap inspection. 

  

Buying a home is probably the most expensive purchase you will ever make.  This is no time to shop for a cheap inspection.  The cost of a home inspection is small relative to the value of the home being inspected.  The additional cost of hiring a certified inspector is almost insignificant by comparison.  As a home buyer, you have recently been crunching the numbers, negotiating offers, adding up closing costs, shopping for mortgages, and trying to get the best deals.  Don't stop now!  Don't let your real estate agent, a "patty-cake" inspector, or anyone else talk you into skimping here.   

   

InterNACHI front-ends its membership requirements.  InterNACHI turns down more than half the inspectors who want to join because they can't fulfill the membership requirements.  

  

InterNACHI-certified inspectors perform the best inspections, by far.  InterNACHI-certified inspectors earn their fees many times over.  They do more, they deserve more and -- yes -- they generally charge a little more.  Do yourself a favor...and pay a little more for the quality inspection you deserve.

15 Tools Every Homeowner Should Own

15 Tools Every Homeowner Should Own
by Nick Gromicko and Ben Gromicko

The following items are essential tools, but this list is by no means exhaustive. Feel free to ask an InterNACHI inspector during your next inspection about other tools that you might find useful.

1.  Plunger
A clogged sink or toilet is one of the most inconvenient household problems that you will face. With a plunger on hand, however, you can usually remedy these plumbing issues relatively quickly. It is best to have two plungers -- one for the sink and one for the toilet.

2.  Combination Wrench Set
One end of a combination wrench set is open and the other end is a closed loop. Nuts and bolts are manufactured in standard and metric sizes, and because both varieties are widely used, you’ll need both sets of wrenches. For the most control and leverage, always pull the wrench toward you, instead of pushing on it. Also, avoid over-tightening.

3.  Slip-Joint Pliers
Use slip-joint pliers to grab hold of a nail, a nut, a bolt, and much more. These types of pliers are versatile because of the jaws, which feature both flat and curved areas for gripping many types of objects. There is also a built-in slip-joint, which allows the user to quickly adjust the jaw size to suit most tasks.

4.  Adjustable Wrench

Adjustable wrenches are somewhat awkward to use and can damage a bolt or nut if they are not handled properly. However, adjustable wrenches are ideal for situations where you need two wrenches of the same size. Screw the jaws all the way closed to avoid damaging the bolt or nut.

5.  Caulking Gun
Caulking is the process of sealing up cracks and gaps in various structures and certain types of piping. Caulking can provide noise mitigation and thermal insulation, and control water penetration. Caulk should be applied only to areas that are clean and dry.

6.  Flashlight
None of the tools in this list is of any use if you cannot visually inspect the situation. The problem, and solution, are apparent only with a good flashlight. A traditional two-battery flashlight is usually sufficient, as larger flashlights may be too unwieldy.

7.  Tape Measure
Measuring house projects requires a tape measure -- not a ruler or a yardstick. Tape measures come in many lengths, although 25 feet is best.  Measure everything at least twice to ensure accuracy.

8.  Hacksaw
A hacksaw is useful for cutting metal objects, such as pipes, bolts and brackets. Torpedo levelHacksaws look thin and flimsy, but they’ll easily cut through even the hardest of metals. Blades are replaceable, so focus your purchase on a quality hacksaw frame.

9. Torpedo Level

Only a level can be used to determine if something, such as a shelf, appliance or picture, is correctly oriented. The torpedo-style level is unique because it not only shows when an object is perfectly horizontal or vertical, but it also has a gauge that shows when an object is at a 45-degree angle. The bubble in the viewfinder must be exactly in the middle -- not merely close.

10.  Safety Glasses / Goggles
For all tasks involving a hammer or a power tool, you should always wear safety glasses or goggles. They should also be worn while you mix chemicals.

11.  Claw Hammer
A good hammer is one of the most important tools you can own.  Use it to drive and remove nails, to pry wood loose from the house, and in combination with other tools. They come in a variety of sizes, although a 16-ounce hammer is the best all-purpose choice.

12.  Screwdriver Set
It is best to have four screwdrivers: a small and large version of both a flathead and a Phillips-head screwdriver. Electrical screwdrivers areWire cutter sometimes convenient, but they're no substitute.  Manual screwdrivers can reach into more places and they are less likely to damage the screw.

13.  Wire Cutters

Wire cutters are pliers designed to cut wires and small nails. The side-cutting style (unlike the stronger end-cutting style) is handy, but not strong enough to cut small nails.

14.  Respirator / Safety Mask
While paints and other coatings are now manufactured to be less toxic (and lead-free) than in previous decades, most still contain dangerous chemicals, which is why you should wear a mask to avoid accidentally inhaling. A mask should also be worn when working in dusty and dirty environments. Disposable masks usually come in packs of 10 and should be thrown away after use. Full and half-face respirators can be used to prevent the inhalation of very fine particles that ordinary facemasks will not stop.

15.  Duct Tape
This tape is extremely strong and adaptable. Originally, it was widely used to make temporary repairs to many types of military equipment. Today, it’s one of the key items specified for home emergency kits because it is water-resistant and extremely sticky.

Are you seeking your first home? Help is available, step by step - http://t.co/0mh3CQp361 #GoogleAlerts

Are you seeking your first home? Help is available, step by step - http://t.co/0mh3CQp361 #GoogleAlerts

— RVA Home Inspections (@RVAHmInspection) June 9, 2015

from Twitter https://twitter.com/RVAHmInspection

June 09, 2015 at 03:59AM
via IFTTT

Attached Garage Fire Hazards

by Nick Gromicko and Kenton Shepard

The purpose of this article is twofold. First, at InterNACHI, we’d like you to take measures to keep your garage free from fire. Fortunately, there are ways this can be done, some of which are described below. Secondly, garage fires do happen, and we’d like you to make sure that a fire cannot not easily spread to the rest of your house. While you can perform many of the recommendations in this article yourself, it is a good idea to hire an InterNACHI inspector to make sure your home is safe from a garage fire.

Why do many garages pose a fire hazard?

• Where are you most likely to do any welding, or any work on your car? These activities require working with all sorts of flammable materials. 
• Water heaters and boilers are usually stored in garages, and they can create sparks that may ignite fumes or fluids. Car batteries, too, will spark under certain conditions. 
• Oil and gasoline can drip from cars. These fluids may collect unnoticed and eventually ignite, given the proper conditions. 
• Flammable liquids, such as gasoline, motor oil and paint are commonly stored in garages. Some other examples are brake fluid, varnish, paint thinner and lighter fluid.

The following tips can help prevent garage fires and their spread:

• If the garage allows access to the attic, make sure a hatch covers this access. 
• The walls and ceiling should be fire-rated. Unfortunately, it will be difficult for untrained homeowners to tell if their walls are Type X fire-rated gypsum. An InterNACHI inspector can examine the walls and ceiling to make sure they are adequate fire barriers.  
• The floor should be clear of clutter. Loose papers, matches, oily rags, and other potentially  flammable items are extremely dangerous if they are strewn about the garage floor. 
• Use light bulbs with the proper wattage, and do not overload electrical outlets. 
• Tape down all cords and wires so they are not twisted or accidentally yanked. 

If there is a door that connects the garage to the living area, consider the following:

• Do not install a pet door in the door! Flames can more easily spread into the living area through a pet door, especially if it’s made of plastic. 
• Does the door have a window? An InterNACHI inspector can inspect the window to tell if it's fire-rated. 
• The door should be self-closing. While it may be inconvenient, especially while carrying groceries into the house from the car, doors should be self-closing. You never know when a fire will happen, and it would be unfortunate to accidentally leave the door open while a fire is starting in the garage. 
• Check the joints and open spaces around the door. Are they tightly sealed? Any openings at all can allow dangerous fumes, such as carbon monoxide or gasoline vapor, to enter the living area. An InterNACHI inspector can recommend ways to seal the door so that fumes cannot enter the living area.

Concerning items placed on the floor, you should check for the following:

• Store your flammable liquids in clearly labeled, self-closing containers, and only in small amounts. Keep them away from heaters, appliances, pilot lights and other sources of heat or flame. 
• Never store propane tanks indoors. If they catch fire, they can explode. Propane tanks are sturdy enough to be stored outdoors.

In summary, there are plenty of things that you can do to prevent garage fires from spreading to the rest of the house, or to keep them from starting in the first place. However, it is highly recommended that you have your garage periodically examined by an InterNACHI inspector.

10 Easy Ways to Save Money & Energy in Your Home

by Nick Gromicko, Ben Gromicko, and Kenton Shepard 

10 Façons Simples de Limiter Votre Consommation énergétique chez Vous

Las 10 maneras fáciles de reducir el consumo de energía en su casa

  

Most people don’t know how easy it is to make their homes run on less energy, and here at InterNACHI, we want to change that. Drastic reductions in heating, cooling and electricity costs can be accomplished through very simple changes, most of which homeowners can do themselves. Of course, for homeowners who want to take advantage of the most up-to-date knowledge and systems in home energy efficiency, InterNACHI energy auditors can perform in-depth testing to find the best energy solutions for your particular home.  

Why make your home more energy efficient? Here are a few good reasons:

• Federal, state, utility and local jurisdictions' financial incentives, such as tax breaks, are very advantageous for homeowners in most parts of the U.S. 
• It saves money. It costs less to power a home that has been converted to be more energy-efficient. 
• It increases the comfort level indoors. 
• It reduces our impact on climate change. Many scientists now believe that excessive energy consumption contributes significantly to global warming. 
• It reduces pollution. Conventional power production introduces pollutants that find their way into the air, soil and water supplies.

1. Find better ways to heat and cool your house. 

As much as half of the energy used in homes goes toward heating and cooling. The following are a few ways that energy bills can be reduced through adjustments to the heating and cooling systems:

• Install a ceiling fan. Ceiling fans can be used in place of air conditioners, which require a large amount of energy. 
• Periodically replace air filters in air conditioners and heaters. 
• Set thermostats to an appropriate temperature. Specifically, they should be turned down at night and when no one is home. In most homes, about 2% of the heating bill will be saved for each degree that the thermostat is lowered for at least eight hours each day. Turning down the thermostat from 75° F to 70° F, for example, saves about 10% on heating costs. 
• Install a programmable thermostat. A programmable thermostat saves money by allowing heating and cooling appliances to be automatically turned down during times that no one is home and at night. Programmable thermostats contain no mercury and, in some climate zones, can save up to $150 per year in energy costs. 
• Install a wood stove or a pellet stove. These are more efficient sources of heat than furnaces. 
• At night, curtains drawn over windows will better insulate the room. 

2. Install a tankless water heater.

Demand-type water heaters (tankless or instantaneous) provide hot water only as it is needed. They don't produce the standby energy losses associated with traditional storage water heaters, which will save on energy costs. Tankless water heaters heat water directly without the use of a storage tank. When a hot water tap is turned on, cold water travels through a pipe into the unit. A gas burner or an electric element heats the water. As a result, demand water heaters deliver a constant supply of hot water. You don't need to wait for a storage tank to fill up with enough hot water. 

3. Replace incandescent lights.

The average household dedicates 11% of its energy budget to lighting. Traditional incandescent lights convert approximately only 10% of the energy they consume into light, while the rest becomes heat. The use of new lighting technologies, such as light-emitting diodes (LEDs) and compact fluorescent lamps (CFLs), can reduce the energy use required by lighting by 50% to 75%. Advances in lighting controls offer further energy savings by reducing the amount of time that lights are on but not being used. Here are some facts about CFLs and LEDs:

• CFLs use 75% less energy and last about 10 times longer than traditional incandescent bulbs. 
• LEDs last even longer than CFLs and consume less energy. 
• LEDs have no moving parts and, unlike CFLs, they contain no mercury.

4. Seal and insulate your home.

Sealing and insulating your home is one of the most cost-effective ways to make a home more comfortable and energy-efficient, and you can do it yourself. A tightly sealed home can improve comfort and indoor air quality while reducing utility bills. An InterNACHI energy auditor can assess  leakage in the building envelope and recommend fixes that will dramatically increase comfort and energy savings.

The following are some common places where leakage may occur:

• electrical receptacles/outlets; 
• mail slots; 
• around pipes and wires; 
• wall- or window-mounted air conditioners; 
• attic hatches; 
• fireplace dampers; 
• inadequate weatherstripping around doors; 
• baseboards; 
• window frames; and 
• switch plates.

Because hot air rises, air leaks are most likely to occur in the attic. Homeowners can perform a variety of repairs and maintenance to their attics that save them money on cooling and heating, such as:  

• Plug the large holes. Locations in the attic where leakage is most likely to be the greatest are where walls meet the attic floor, behind and under attic knee walls, and in dropped-ceiling areas. 
• Seal the small holes. You can easily do this by looking for areas where the insulation is darkened. Darkened insulation is a result of dusty interior air being filtered by insulation before leaking through small holes in the building envelope. In cold weather, you may see frosty areas in the insulation caused by warm, moist air condensing and then freezing as it hits the cold attic air. In warmer weather, you’ll find water staining in these same areas. Use expanding foam or caulk to seal the openings around plumbing vent pipes and electrical wires. Cover the areas with insulation after the caulk is dry. 
• Seal up the attic access panel with weatherstripping. You can cut a piece of fiberglass or rigid foamboard insulation in the same size as the attic hatch and glue it to the back of the attic access panel. If you have pull-down attic stairs or an attic door, these should be sealed in a similar manner. 

5. Install efficient showerheads and toilets.

The following systems can be installed to conserve water usage in homes: 

• low-flow showerheads. They are available in different flow rates, and some have a pause button which shuts off the water while the bather lathers up; 
• low-flow toilets. Toilets consume 30% to 40% of the total water used in homes, making them the biggest water users. Replacing an older 3.5-gallon toilet with a modern, low-flow 1.6-gallon toilet can reduce usage an average of 2 gallons-per-flush (GPF), saving 12,000 gallons of water per year. Low-flow toilets usually have "1.6 GPF" marked on the bowl behind the seat or inside the tank; 
• vacuum-assist toilets. This type of toilet has a vacuum chamber that uses a siphon action to suck air from the trap beneath the bowl, allowing it to quickly fill with water to clear waste. Vacuum-assist toilets are relatively quiet; and
• dual-flush toilets. Dual-flush toilets have been used in Europe and Australia for years and are now gaining in popularity in the U.S. Dual-flush toilets let you choose between a 1-gallon (or less) flush for liquid waste, and a 1.6-gallon flush for solid waste. Dual-flush 1.6-GPF toilets reduce water consumption by an additional 30%.

6. Use appliances and electronics responsibly.

Appliances and electronics account for about 20% of household energy bills in a typical U.S. home. The following are tips that will reduce the required energy of electronics and appliances:

• Refrigerators and freezers should not be located near the stove, dishwasher or heat vents, or exposed to direct sunlight. Exposure to warm areas will force them to use more energy to remain cool.   
• Computers should be shut off when not in use. If unattended computers must be left on, their monitors should be shut off. According to some studies, computers account for approximately 3% of all energy consumption in the United States. 
• Use efficient ENERGY STAR-rated appliances and electronics. These devices, approved by the U.S. Department of Energy and the Environmental Protection Agency’s ENERGY STAR Program, include TVs, home theater systems, DVD players, CD players, receivers, speakers, and more. According to the EPA, if just 10% of homes used energy-efficient appliances, it would reduce carbon emissions by the equivalent of 1.7 million acres of trees. 
• Chargers, such as those used for laptops and cell phones, consume energy when they are plugged in. When they are not connected to electronics, chargers should be unplugged. 
• Laptop computers consume considerably less electricity than desktop computers.

7. Install daylighting as an alternative to electrical lighting.

Daylighting is the practice of using natural light to illuminate the home's interior. It can be achieved using the following approaches: 

• skylights. It’s important that they be double-pane or they may not be cost-effective. Flashing skylights correctly is key to avoiding leaks; 
• light shelves. Light shelves are passive devices designed to bounce light deep into a building. They may be interior or exterior. Light shelves can introduce light into a space up to 2½ times the distance from the floor to the top of the window, and advanced light shelves may introduce four times that amount;
• clerestory windows.  Clerestory windows are short, wide windows set high on the wall. Protected from the summer sun by the roof overhang, they allow winter sun to shine through for natural lighting and warmth; and 
• light tubes.  Light tubes use a special lens designed to amplify low-level light and reduce light intensity from the midday sun. Sunlight is channeled through a tube coated with a highly reflective material, and then enters the living space through a diffuser designed to distribute light evenly.

8. Insulate windows and doors.

About one-third of the home's total heat loss usually occurs through windows and doors. The following are ways to reduce energy lost through windows and doors:

• Seal all window edges and cracks with rope caulk. This is the cheapest and simplest option. 
• Windows can be weatherstripped with a special lining that is inserted between the window and the frame. For doors, apply weatherstripping around the whole perimeter to ensure a tight seal when they're closed. Install quality door sweeps on the bottom of the doors, if they aren't already in place. 
• Install storm windows at windows with only single panes. A removable glass frame can be installed over an existing window. 
• If existing windows have rotted or damaged wood, cracked glass, missing putty, poorly fitting sashes, or locks that don't work, they should be repaired or replaced.

9. Cook smart.

An enormous amount of energy is wasted while cooking. The following recommendations and statistics illustrate less wasteful ways of cooking: 

• Convection ovens are more efficient that conventional ovens. They use fans to force hot air to circulate more evenly, thereby allowing food to be cooked at a lower temperature. Convection ovens use approximately 20% less electricity than conventional ovens. 
• Microwave ovens consume approximately 80% less energy than conventional ovens. 
• Pans should be placed on the matching size heating element or flame.  
• Using lids on pots and pans will heat food more quickly than cooking in uncovered pots and pans. 
• Pressure cookers reduce cooking time dramatically. 
• When using conventional ovens, food should be placed on the top rack. The top rack is hotter and will cook food faster.  

10. Change the way you do laundry.

• Do not use the medium setting on your washer. Wait until you have a full load of clothes, as the medium setting saves less than half of the water and energy used for a full load. 
• Avoid using high-temperature settings when clothes are not very soiled. Water that is 140° F uses far more energy than 103° F for the warm-water setting, but 140° F isn’t that much more effective for getting clothes clean.
• Clean the lint trap every time before you use the dryer. Not only is excess lint a fire hazard, but it will prolong the amount of time required for your clothes to dry. 
• If possible, air-dry your clothes on lines and racks. 
• Spin-dry or wring clothes out before putting them into a dryer. 

Homeowners who take the initiative to make these changes usually discover that the energy savings are more than worth the effort. InterNACHI home inspectors can make this process much easier because they can perform a more comprehensive assessment of energy-savings potential than the average homeowner can.